No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Construcción sin plomo y acabado en oro cepillado
El relleno de olla CAKIONG está diseñado con cuerpo de latón sólido premium con acabado dorado cepillado. Estructura de latón, asegurándose de que el agua que pasa a través del relleno de la olla sea natural, higiénico, saludable y seguro para tus familias, añade elegancia a tu cocina.
Grifo de llenado de olla montado en la pared
Cartucho de cerámica de latón macizo
Este cartucho de calidad premium puede sobrevivir a 500.000 veces la prueba de apertura y cierre, sin fugas, asegurando un uso fiable sin goteo y un rendimiento duradero para la vida.
CAKIONG - Grifo de pared
Pezón de latón estándar de EE. UU
1 pieza de NPT1/2" a NPSM 1/2" tetina de latón viene junto con el relleno de olla
más conveniente.
Alto caudal de agua
La alta tasa de agua puede llenar las ollas o sartenes grandes muy rápidamente.
Tasa de flujo: 4 gpm @ 60 psi, 15 L/min @ 414 kPa
El paquete incluye:
1. Grifo de llenado de olla
2. Tetón de latón
3. Base del grifo
4: Cubierta decorativa
Válvula de repuesto 5.1pc
6. Herramientas de montaje
7. Manual de instrucciones de instalación
Grifo de llenado de olla
Grifo de relleno negro mate
Acabado negro mate
Grifo de llenado de olla para montaje en pared de un solo agujero grifo de dos asas con brazo oscilante, acabado negro mate
Grifo de relleno de níquel cepillado
Acabado en níquel cepillado
Combinación de estilo tradicional y moderno, el diseño de acabado de níquel cepillado puede transformar cualquier cocina en un espacio de trabajo culinario de alta gama, decorar tu cocina y hacer tu hogar más hermoso.
Grifo de relleno de olla de oro cepillado
Acabado en oro cepillado
Grifo de cocina de relleno de olla de oro cepillado montado en la pared de una sola manija con brazo oscilante de doble articulación
Customer
Comentado en los Estados Unidos el 30 de agosto de 2021
The pot filler feels sturdy and well made. However, leaving comments on some key points that you need to consider for install success.Tip #1We had issues with water leaks between the NPT male x 1/2'' NPSM male connector nipple and the pot filler when using 3 wraps of Teflon tape only. The pot filler has a female NPSM connection and helps make fine adjustments between your backsplash level and the depth of your water connection behind. However, the NPSM connection does not have a taper to help it seal or an o-ringed connection (hard to do due to the fine adjustment requirement). This caused me to remove my freshly installed backsplash to find the water leak source.Make sure to wrap min. 2 wraps Teflon tape at thread start and consider adding extra wraps towards the rear of thread to make a tapered edge for the pot filler to seal into (we used 4-5 wraps at end). Get some T plus 2 thread sealer and apply liberally to male connector - this product has PTFE fibers in it and helps with sealing any small leak paths. It will seal straight away no need to wait for it to set or harden. Recommend to flush pot-filler once water is on to remove any excess thread sealant before use. You may see some thread sealant in the water - keep flushing until it's fully gone.Tip # 2When running water pipe behind backsplash make sure that both pipe and backsplash wall is reinforced. Pot-filler is heavy when fully extended and under the load of water pressure hence will require extra reinforcement to prevent any sag or damage to the newly installed tile. We added 2 x 4's between studs for this purpose. The pot filler has a mounting plate that is fitted before connection the NPSM connection - plan to have the 4 x screws driven into those reinforcements to get the required structural strength for the pot filler.Tip # 3Decide if you want a cold or hot water pot filler, there are also options that give you either option. Helps to know which option you want to plan for the water pipe connection(s).Tip # 4We had a gas pipe that was running in the center of our preferred pot-filler connection. Due to this, we positioned the pot filler off-center and it looks just fine. The pot-filler when folded against the wall hides this and most importantly the tap reaches all burner - possible pot locations.
Aldous Schenk
Comentado en los Estados Unidos el 30 de octubre de 2021
I priced out pot fillers from the big names, which were on average 3X to 5X more expensive than this one, so I took and chance and I'm glad I did. Very well made and packaged, comes with all installation tools (including Teflon tape) and thorough instructions. Installation was easy and the faucet is super sturdy, with just the right amount of resistance when you move it - not too tight, not too loose. Gold color is a light brushed gold - doesn't exactly match the brushed brash finish of my Kohler faucet, but its close enough. Nice to find a well made item at such a great price.EDIT: both shut-off valves failed within two years of installation, resulting in a serious, damaging leak.
dct
Comentado en los Estados Unidos el 27 de septiembre de 2019
No issues yet, will update if there are issues.
Productos recomendados
Mex $2,764.16
Mex $ 1,243 .00 Mex $1,243.00
Mex $2,836.37
Mex $ 1,219 .00 Mex $1,219.00
Mex $3,433.83
Mex $ 1,579 .00 Mex $1,579.00